Products
  
 
  Massage Bathtub
  Steam Bathroom
  Outdoor Spa
  Shower Enclosure
  Antique Bathtub
  Sauna Room
  Bathroom Cabinet
  Whirlpool Spa
 
ACEM Sarl - 1880 BEX - CH
Contact: Mr. Manap
Tel:    +41(0) 24 463 40 05
Fax:  + 41(0) 24 463 40 07
Mobile: +41(0)79 552 85 45
E-mail: info@acem.ch



ACEM Sarl Switzerland
Contact: Mr. Manap
Tel: +41(0) 24 463 40 05
Fax: + 41(0) 24 463 40 07
Natel: +41(0)76 223 02 00
E-mail: info@acem.ch

SHOWROOM
Add: Route du Grand Saint Bernard, 5
1880 Bex
Tel: +41(0) 24 463 40 05

Representative office France
Contact: Lucimary Carneiro
Natel: +33(0)6 08 97 51 63
Fax: +33(0)4 50 79 06 99
E-mail: info-france@acem.ch

Exposition in France region Haute-savoie
Add: ECODECO
400 AVENUE DE LA RIVE
74500 AMPHION LE BAINS
Tel:+33(0)450714564

Representative office Germany
Contact: Mr. E. Manap
Tel: +49 15204271143
E-mail: info-allemagne@acem.ch

MEXDA China, Exportation
Contact : Louise XU
Tel: +86 757 88 21 88 10
Fax: +86 757 88 21 88 01
Mobile: +8613928500766
Email: info-china@acem.ch











  FAQ
 
 
Massage Bathtub :
Breakdown phenomenon and settlement:
Phenomenon Reasons Maintenance
No power or electricity leaking protection device is activated 1. Electricity leaking protection device cut off
power source when electricity line is not well
connected.
2. Power or electricity circuit have phenomenon
of electricity leaking.		 1. check and reconnect the wiring system.
2. check the power source, electricity
circuit and ground line.
Water Jets are
not working.		 1. check the system whether is on.
2. the impeller of water pump doesn't rotate.
3. water pump is broken which caused by
working without water coming in.		 1. turn on the system.
2. check through and remove the garbage
which is inside the pump. Switch pipe
can be removed.
3.install a new water pump
The intensity of
hydro-massage
cannot be adjusted		 1. water pump's suction has not enough power.
2. air adjustment valve is abnormal.
3. jets or nozzles are blocked.		 1. check the water pump whether is working normally
2. change the air adjustment valve.
3. remove things which are blocking the jets.
Water leaks from
the pipes
 1. seal ring is broken.
2. screws doesn't lock tightly.
3. pipes doesn't seal properly.		 1. chang seal ring.
2. lock the screws tightly.
3. re-seal the silicone.
4. change water pipe
Jets shower can
not be work. 		1. voltage is abnormal
2. Switch cannot be work
3. control panel cannot be work.
3. water in electromagnetism valve is be blocked		 1. please use it at the normal situation of voltage.
2. check and change the switch.
3. maintain and change the control panel.
4. get rid of mess of the jets.
No lighting 1. The bulb is broken.
2. power line is disconnected.
3. control panel is broken.		 1. change a new bulb..
2. re-connect the circuit..
3. maintain or change control panel
Cleaning and Maintenance:
1. The daily maintenance should be cleaned with ordinary detergent and soft cloth. Please do not use the detergent which contains acetone or ammonia liquid. If there marks or something like glue on the surface of bathtub, just polish it with soft cloth dipping with gas.
2. If there are scratches on bathtub surface, please polish it with 1500# frosted paper dipping with liquid and burnish it with toothpaste. It will be shining again after that.
3. If there are furring on the surface of bathtub, it can be take away by mild acid detergent, for example wipe the bathtub with lemon juice or vinegar which be heated.
4. Do not wipe the chrome plated spare parts all the time, and do not get in touch with chemical detergent etc. Otherwise the surface of chrome plated will be destroyed. The product should be clean by soft cloth other than coarse cloth.
5. To check the water pipe regularly in order to avoid troubles from crack of water pipes or blocked inside.
6. If there are something such as hair stuck inside the jets, then just to twist out the jets and remove it.
7. To clean hydro-massage equipment: To full fill hot water which is 40'C, and pour 2g/L detergent, start hydro-massage function more than 5 minutes, then turn off the massage function and drain out the water. Next, to full fill cold water and start hydro-massage function for 3 minutes, then turn off the massage function and drain out the water, at last, to dry the bathtub with towel.
8. Filter should be clean once a week.
9. Keep out from combustibles and goods which over 80°C to avoid fire disaster and damage the product.
10. The bathtub should be transported carefully. Do not lay heavy things on it and do not bump and shaking the tub. If the bathtub has not been used for a long time, drain out the water of the bathtub and keep it in a dry and ventilate environment. Avoid corrosive gas.

[ Page(1) | Page(2) ]





|
|
|
|
|
|
|